An administrator receives reports of many interferers in the wireless network and wants to get the location of these interferers from the maps in Cisco Prime Infrastructure.

When looking at the floor plans/maps, the administrator does not see any interferers, but can see all wireless clients located successfully.

Which two statements define the cause of the issue? (Choose two.)

What is the difference between PIM sparse mode and PIM dense mode?

An engineer has configured Media Stream on the WLC and must guarantee at least 2 Mbps stream per user. Which RRC template should the engineer use?

Refer to the exhibit. Which two items must be supported on the VoWLAN phones to take full advantage of this WLAN configuration? (Choose two.)

Which configuration is applied to prevent the network from a Layer 2 flooding of multicast frames with a seamless transfer of multicast data to the client when roaming from one controller to another?

An engineer is using Cisco Prime Infrastructure reporting to monitor the state of security on the WLAN. Which output is produced when the Adaptive wIPS Top 10 AP report is run?

WPA2 Enterprise with 802.1X is being used for clients to authenticate to a wireless network through a Cisco ISE server. For security reasons, the network engineer wants to ensure that only PEAP authentication is used. The engineer sent instructions to clients on how to configure the supplicants, but the ISE logs still show users authenticating using EAP-FAST. Which action ensures that access to the network is restricted for these users unless the correct authentication mechanism is configured?

An engineer configures a Cisco Aironet 600 Series OfficeExtend AP for a user who works remotely. What is configured on the Cisco WLC to allow the user to print a printer on his home network?

The IT manager is asking the wireless team to get a report for all guest user associations during the past two weeks. In which two formats can Cisco Prime save this report? (Choose two.)

On a branch office deployment, it has been noted that if the FlexConnect AP is in standalone mode and loses connection to the WLC, all clients are disconnected, and the SSID is no longer advertised. Considering that FlexConnect local switching is enabled, which setting is causing this behavior?

After looking in the logs, an engineer notices that RRM keeps changing the channels for non-IEEE 802.11 interferers. After surveying the area, it has been decided that RRM should not change the channel. Which feature must be enabled to ignore non-802.11 interference?

What is the maximum time range that can be viewed on the Cisco DNA Center issues and alarms page?

What must be configured on ISE version 2.1 BYOD when using Single SSID?

In a Cisco WLAN deployment, it is required that all Aps from branch1 remain operational even if the control plane CAPWAP tunnel is down because of a WAN failure to headquarters. Which operational mode must be configured on the APs?

You enter the command or a Cisco Catalyst 3850 Series Switch that runs Cisco ISO X

E.  

A company is deploying wireless PCs on forklifts within its new 10,000-square-foot(3048-square-rneter) facility.

The clients are configured for PEAP-MS-CHAPv2 with WPA TKIP. Users report that applications frequently drop when the clients roam between access points on the floor. A professional site survey was completed.

Which configuration change is recommended to improve the speed of client roaming?

Which AP model of the Cisco Aironet Active Sensor is used with Cisco DNA Center?

A corporation has employees working from their homes. A wireless engineer must connect 1810 OEAP at remote teleworker locations. All configuration has been completed on the controller side, but the network readiness is pending. Which two configurations must be performed on the firewall to allow the AP to join the controller? (Choose two.)

Where is a Cisco OEAP enabled on a Cisco Catalyst 9800 Series Wireless Controller?

Which two steps are needed to complete integration of the MSE to Cisco Prime Infrastructure to track the location of clients/rogues on maps? (Choose two.)

Refer to the exhibit.

An administrator notices slower location updates from the controller to Cisco CMX. Which command must be configured to get an update every 5 seconds for rogues?

The security policy mandates that only controller web management traffic is allowed from the IT subnet. In testing, an engineer is trying to connect to a WLAN with Web Authentication for guest users, but the page is timing out on the wireless client browser. What is the cause of the issue?

A wireless engineer has performed a Wireshark ccapture on an 802.1x authentication process to troubleshoot a connectivity issue.

Which two types of packet does the EAP contain? (Choose two.)

An engineer is implementing profiling for BYOD devices using Cisco IS

E.  

What must be configured on the Global Configuration page of the WLC for an AP to use 802.1x to authenticate to the wired infrastructure?

Which EAP method can an AP use to authenticate to the wired network?

A user is trying to connect to a wireless network that is configured for WPA2-Enterprise security using a corporate laptop. The CA certificate for the authentication server has been installed on the Trusted Root Certification Authorities store on the laptop. The user has been prompted to enter the credentials multiple times, but the authentication has not succeeded. What is causing the issue?

A corporation is spread across different countries and uses MPLS to connect the offices. The senior management wants to utilize the wireless network for all the employees. To ensure strong connectivity and minimize delays, an engineer needs to control the amount of traffic that is traversing between the APs and the central WL

C.  

An engineer is configuring multicast for two WLCs. The controllers are in different physical locations and each handles around 500 wireless clients. How should the CAPWAP multicast group address be assigned during configuration?

A new MSE with wIPS service has been installed and no alarm information appears to be reaching the MSE from controllers. Which protocol must be allowed to reach the MSE from the controllers?

An engineer has configured passive fallback mode for RADIUS with default timer settings. What will occur when the primary RADIUS fails then recovers?

Refer to the exhibit.

An engineer is creating an ACL to restrict some traffic to the WLC CPU. Which selection must be made from the direction drop- down list?