Exclusive Black Friday Deal: 70% Off All Exam Bundles! Use coupon code below to unlock your savings! - Ends in 0d 00h 00m 00s - Coupon code: Friday70

Free RCPE Certified Professional WAN Optimization Practice Questions

Question # 51

In order to reset the admin password that has been lost, the procedure can be done via what type of connection to a Steelhead appliance?

Options:

A.  

SSH over Primary interface IP

B.  

SSH over AUX interface IP

C.  

SSH over in-path interface IP

D.  

Serial cable connection

E.  

Password recovery can not be done on a Steelhead appliance

Discussion 0
Question # 52

What probe is being used in the inner channel between two Steelhead appliances when using Full Transparency in hex?

Options:

A.  

0x4e

B.  

0x4d

C.  

0x4c

D.  

0x4b

E.  

No probe is used

Discussion 0
Question # 53

What is the command to clear all statistics on a Steelhead appliance?

Options:

A.  

(config) # stats clear-all

B.  

(config) # clear-all stats

C.  

(config) # reset stats

D.  

(config) # reload stats clean

E.  

(config) # clear stats

Discussion 0
Question # 54

During an upgrade, what steps are necessary to convert VM slots for use in Steelhead EX v2.0? (Select 3)

Options:

A.  

Transfer the slot to a remote server (or download from a browser).

B.  

Convert the slot or package for use on a Steelhead EX v2.0 appliance and adjust its properties, if necessary.

C.  

Configure the slots to not start before upgrading to Steelhead EX v2.0.

D.  

Create compressed versions of your existing VSP slots.

E.  

Any VM slots that do not use data flow will be automatically converted during the upgrade to Steelhead EX v2.0.

Discussion 0
Question # 55

Refer to the exhibit.

Question # 55

In order to achieve optimization using auto-discovery for traffic coming from site C and destined to site A in the exhibit, which configuration below would be required?

Options:

A.  

In-path fixed-target rule on site B Steelhead appliance pointing to Site A Steelhead appliance

B.  

Peering rule on site B Steelhead appliance passing through probes from site C

C.  

Peering rule on site B Steelhead appliance passing through probe responses from site A

D.  

Both A and C

E.  

Both B and C

Discussion 0
Question # 56

You are configuring HighSpeed TCP in an environment with an OC-3 (155Mb/s) and 60 milliseconds of round-trip latency. You know that the rule of thumb is to set the WAN router queue length to BDP for the link. Assuming 1500 byte packets, the queue length for this link would be closest to: (Hint: Use the calculator)

Options:

A.  

3,110 packets

B.  

6,220 packets

C.  

775 packets

D.  

150 packets

E.  

10,000 packets

Discussion 0
Question # 57

When deploying policy-based routing for multiple Steelhead appliances in a cluster, the router should be configured to: (Select 2)

Options:

A.  

Set IP next-hop address to the virtual IP address of the Steelhead appliance cluster

B.  

Set IP next-hop addresses for each Steelhead appliance

C.  

Check the state level information on each Steelhead appliance via SLA or CDP

D.  

Auto-detect the Steelhead appliance clustering protocol

E.  

Check the state level information on the virtual IP address of the Steelhead appliance cluster

Discussion 0
Question # 58

What is the default Connection Forwarding keep alive interval?

Options:

A.  

1 second

B.  

3 seconds

C.  

5 seconds

D.  

10 seconds

E.  

15 seconds

Discussion 0
Question # 59

When two or more Steelhead appliances are configured with Connection Forwarding in such environments as WCCP clustering, what feature will allow remaining Steelhead appliances to continue to provide optimization for new connections when one unit fails?

Options:

A.  

In-Path Neighbor Failur

E.  

Allow

B.  

WCCP neighbor active

C.  

Minimum cluster count set to 1

D.  

Maximum cluster count set to 2

E.  

This cannot be done on Steelhead appliances

Discussion 0
Question # 60

What is the primary purpose of enabling Multiple Interface Support on the Interceptor appliance?

Options:

A.  

It allows for the ability to support multiple NICs on the Interceptor appliance.

B.  

It allows the Interceptor appliance to communicate with Steelhead appliances and other Interceptor appliances using more than one in-path interface.

C.  

It allows the Interceptor appliance to communicate using multicast to in-path interfaces on the Steelhead appliances.

D.  

It allows the Interceptor appliance to be managed by in-path interfaces as well as the primary interface.

Discussion 0

830-01 PDF

830-01 PDF (Printable)
$46.5
$154.99

830-01 Testing Engine

830-01 PDF (Printable)
$51
$169.99

830-01 PDF + Testing Engine

830-01 PDF (Printable)
$63.9
$212.99

Free Exams Sample Questions