Exclusive Black Friday Deal: 70% Off All Exam Bundles! Use coupon code below to unlock your savings! - Ends in 0d 00h 00m 00s - Coupon code: Friday70

Free Welding Inspection and Metallurgy Exam Practice Questions

Question # 11

If an individual changes an essential variable in the WPS, the individual must:

Options:

A.  

Re-qualify the PQR.

B.  

Re-qualify the WPS.

C.  

Record the change on the existing WPS.

D.  

List the change as a supplement to the WPS.

Discussion 0
Question # 12

The deflection of an arc from its normal path that is a result of magnetic forces is referred to as:

Options:

A.  

Arc drift.

B.  

Arc strike.

C.  

Arc blow.

D.  

Arc deflection.

Discussion 0
Question # 13

Stud arc welding is a specialized process predominantly limited to welding:

Options:

A.  

Non-load-bearing welds.

B.  

Insulation and refractory pins.

C.  

Flat position welds.

D.  

Non-pressure-containing welds.

Discussion 0
Question # 14

Which of the following is an important aspect of a qualified WPS?

Options:

A.  

Welder qualification

B.  

Maintaining project schedule

C.  

Welding program effectiveness

D.  

Fabrication quality control

Discussion 0
Question # 15

Hardenability of a steel can be an indirect indicator of:

Options:

A.  

Weldability

B.  

Toughness

C.  

Strength

D.  

Cooling rate

Discussion 0
Question # 16

Which of the following statements concerning electrode storage in ovens is true?

Options:

A.  

Electrodes should never be stored in an oven that is used for food storage.

B.  

Low-hydrogen electrodes may be stored in ovens with cellulose-based electrodes, but must be in their original, unopened containers.

C.  

Electrode ovens should be heated by any means, but must have automatic heat controls and visible temperature indicators.

D.  

Low-hydrogen electrodes should never be stored with stainless-steel electrodes.

Discussion 0
Question # 17

Hot tapping and in-service welding should be carried out only with:

Options:

A.  

Steels that have a carbon equivalent below 0.30.

B.  

Cellulosic-type electrodes to reduce penetration.

C.  

Low-hydrogen consumables and electrodes.

D.  

Low-hydrogen root pass and cellulosic weld out.

Discussion 0
Question # 18

When verifying that the filler metal selection is appropriate for the base metal being welded, an inspector should consider:

Options:

A.  

Chemical composition.

B.  

Tensile strength to be higher than the base metal.

C.  

Acceptability of physical properties.

D.  

Need for postweld heat treatment (PWHT).

Discussion 0
Question # 19

Mechanical tests are required to qualify a welding procedure to document that the properties of the weldment meet which of the following?

Options:

A.  

The expected load for which the weld will be subject.

B.  

The minimum established acceptance criteria.

C.  

The requirements as established in ASME Section XI.

D.  

The same criteria required for welder qualification.

Discussion 0
Question # 20

At least how far on each side of the weld should preheat be maintained?

Options:

A.  

2 in. (5.1 cm)

B.  

3 in. (7.6 cm)

C.  

4 in. (10.2 cm)

D.  

6 in. (15.2 cm)

Discussion 0

API-577 PDF

API-577 PDF (Printable)
$46.5
$154.99

API-577 Testing Engine

API-577 PDF (Printable)
$51
$169.99

API-577 PDF + Testing Engine

API-577 PDF (Printable)
$63.9
$212.99

Free Exams Sample Questions