Exclusive Black Friday Deal: 70% Off All Exam Bundles! Use coupon code below to unlock your savings! - Ends in 0d 00h 00m 00s - Coupon code: Friday70

Free Certified Wireless Design Professional Practice Questions

Question # 51

You have designed a WLAN with a plan for 87 APs in a large office building. The customer has informed you that the budget is not as large as they hoped and they can only purchase 53 APs. What action should be taken?

Options:

A.  

Simply increase the output power of the APs by 30 percent to accommodate the smaller number of purchased APs

B.  

Perform a complete redesign of the wireless network and inform the customer if some original requirements cannot be accomplished

C.  

Remove as many walls as possible within the facility so that the signals can travel a greater distance

D.  

Use only 2.4 GHz radios because the signals can be received at a greater distance

Discussion 0
Question # 52

Which one of the following is an essential metric to measure when performing a survey and design for VoIP across WLANs?

Options:

A.  

Throughput rates above 50 Mbps

B.  

Data rates above 100 Mbps

C.  

Latency

D.  

PoE provided to wireless handsets

Discussion 0
Question # 53

What is the best method of gathering attenuation measurements from wall materials?

Options:

A.  

After measuring the RSSI in free space 5 meters (16.5 feet) apart, put an AP 4 meters (13 feet) away from the wall on one side and your measuring device 1 meter (3.2 feet) away from the wall minus the width of the wall. Take measurements and compare the difference.

B.  

Use the pre-built attenuation values in the predictive design tools as they are more accurate than free-space metrics gathered with commercial devices.

C.  

After measuring the RSSI in free space 1 meter (3 feet) apart, put an AP 0.32 meters (1 feet) away from the wall on one side and your measuring device 0.67 meters (2 feet) away from the wall on the other side. Take measurements and compare the difference.

D.  

Look on the Internet for attenuation values for each one of the materials that might attenuate the Wi-Fi signal using the material providers' websites.

Discussion 0
Question # 54

In a multiple channel architecture (MCA) network supporting 802.1X authentication, what aspect of WLAN design affects client roaming efficiency and effectiveness?

Options:

A.  

PHY standard used by the AP

B.  

Key caching protocols

C.  

Cipher suite

D.  

PHY standard used by client

Discussion 0
Question # 55

Which vertically polarized antenna is best suited for a WLAN infrastructure with access points mounted on a ceiling over 6 meters high, where all client stations operate from the floor level?

Options:

A.  

Patch

B.  

Dish

C.  

Grid

D.  

Low-gain dipole

Discussion 0
Question # 56

In a convention center, you have received complaints about the WLAN infrastructure. At this moment, there are only two APs in one auditorium. After analyzing the situation, you determined that there are more client devices than the infrastructure was designed for. There are only two APs to support more than 300 devices using Wi-Fi at the same time. What should you do to make the Wi-Fi work as expected?

Options:

A.  

Redesign the entire WLAN

B.  

Upgrade the Ethernet connections to MultiGig

C.  

Quickly add more APs

D.  

Turn up the output power on the APs so that they can handle more clients

Discussion 0
Question # 57

A customer wants to deploy a WLAN that employs centralized forwarding. What LAN requirements should you look for?

Options:

A.  

High-speed Ethernet links

B.  

Layer 3 at the access layer

C.  

Layer 2 at the distribution layer

D.  

Routing redundancy protocol

Discussion 0
Question # 58

Why does a frame transmitted at 1 Mbps have a greater usable range than the same frame transmitted at 54 Mbps?

Options:

A.  

Free space path loss causes greater signal dispersion for higher rate transmissions.

B.  

Receiver sensitivity requirements are lower for frames transmitted with less complex modulation and coding.

C.  

To improve reliability, 802.11 STAs increase transmit power as the signaling rate decreases.

D.  

Lower data rate RF transmissions travel at higher speeds and are less likely to experience collisions.

Discussion 0
Question # 59

Main Topic:Designing for Specific Applications

Question:

What are some common problems with short (12 or fewer characters) ASCII passphrases in WPA/WPA2-Personal networks?

Options:

A.  

They are more susceptible to dictionary attacks than longer passphrases.

B.  

They lead to weak group keys in a BSS.

C.  

They only produce a 64-bit PMK instead of a 256-bit PMK.

D.  

Very few AP and client vendors support entry of an ASCII-based passphrase.

Discussion 0
Question # 60

After designing a WLAN infrastructure using predictive design software. What's the best way to validate the predictive design in the physical space before deployment, if time and budget allow for it?

Options:

A.  

Perform an AP-on-a-Stick survey using AP locations based upon the predictive design to confirm each AP's placement.

B.  

Deploy all of the APs as they're shown in the predictive design and perform a passive site survey.

C.  

Deploy all of the APs as they're shown in the predictive design and perform an active site survey.

D.  

Use a client device positioned where the APs will be installed and measure the signal from the client device.

Discussion 0

CWDP-305 PDF

CWDP-305 PDF (Printable)
$46.5
$154.99

CWDP-305 Testing Engine

CWDP-305 PDF (Printable)
$51
$169.99

CWDP-305 PDF + Testing Engine

CWDP-305 PDF (Printable)
$63.9
$212.99

Free Exams Sample Questions