Exclusive Black Friday Deal: 70% Off All Exam Bundles! Use coupon code below to unlock your savings! - Ends in 0d 00h 00m 00s - Coupon code: Friday70

Free HCIP-Datacom-Advanced Routing & Switching Technology V1.0 Practice Questions

Question # 31

The figure shows the debugging information on an OSPF router. Which of the following is the router ID of this router?

Question # 31

Options:

A.  

10.0.2.2

B.  

10.0.12.2

C.  

10.0.12.1

D.  

10.0.1.1

Discussion 0
Question # 32

A network engineer obtains a multicast data frame whose destination MAC address is 01-00-5e-00-01-01. Given this, which of the following cannot be the destination IPv4 address of this frame?

Options:

Options:

A.  

225.0.1.1

B.  

224.0.1.1

C.  

239.128.1.1

D.  

224.0.0.1

Discussion 0
Question # 33

A BGP router receives a BGP route with the AS_Path attribute 100 200 300. If the router wants to deny this route, which of the following commands are used?

Options:

A.  

ip as-path-filter 1 deny 00$

B.  

ip as-path-filter 1 deny .*

C.  

ip as-path-filter 1 deny 200

D.  

ip as-path-filter 1 deny 00.*30

Discussion 0
Question # 34

A network engineer provides a troubleshooting report after rectifying a fault. The actual network is simplified into the one shown in the figure, where:

    R1 and R2 both have OSPF enabled.

    R1 and R2 function as the gateways for PC1 and PC2, respectively.

Given this, which of the following statements are true?

Question # 34

Options:

Options:

A.  

R1 can ping 192.168.1.22.

B.  

R1 can ping 192.168.1.21.

C.  

R2 can ping 192.168.1.2.

D.  

PC1 and PC2 cannot ping each other.

Discussion 0
Question # 35

On the OSPF network shown in the figure, the cost values of links are marked, and OSPF IP FRR is enabled on R1. Which of the following statements are true?

Question # 35

Options:

A.  

No backup path can be established between R1 and 10.0.3.3/32.

B.  

If SI is powered off, R1 directly uses the backup path to forward packets to R3.

C.  

If BFD (with default detection parameters) is enabled on the entire network and the link between R2 and SI is disconnected, R1 can quickly detect the OSPF adjacency fault.

D.  

If the link between R1 and SI is disconnected, R1 directly uses the backup path to forward packets to R3.

Discussion 0
Question # 36

On the network shown in the figure, IS-IS IPv6 runs on R2, R6, and R3, and the IPv6 address of Loopback0 on R6 is 2000::6/128. OSPFv3 runs on other links. Area 1 is a stub area, and area 2 is an NSS

A.  

ISIS routes are imported to OSPFv3 on R2 and R3. Which of the following methods can enable R4 to ping 2000: :6?

Question # 36

Options:

A.  

Configure the ipv6 default-route-advertise always level-1 command in the IS-IS process of R3.

B.  

Configure the ipv6 default-route-advertise always level-1 command in the IS-IS process of R2.

C.  

Configure the attached-bit advertise always command in the IS-IS process of R3.

D.  

Configure the attached-bit advertise always command in the IS-IS process of R2.

Discussion 0
Question # 37

On the OSPF network shown in the figure, area 1 and area 2 are common areas. The IP address of Loopback0 on R5 is 10.0.5.5/32, and OSPF is enabled on this interface. If the abr-summary 10.0.5.0 255.255.255.0 command is run in area 2 (where R1 resides), which of the following routers have the route 10.0.5.0/24 in their routing tables?

Question # 37

Options:

A.  

R5

B.  

R2

C.  

R3

D.  

R4

Discussion 0
Question # 38

On the OSPF network shown in the figure, area 1 is an NSSA, area 2 is a stub area, and R4 imports an external route 10.0.4.4/32. The router ID of each router is 10.0.X.X, where X is the router number. The asbr-summary 10.0.4.0 255.255.255.0 command is configured in the OSPF processes of R1 and R3.

Match the following descriptions of routing tables with the corresponding routers:

Question # 38

Options:

Discussion 0
Question # 39

On the network shown in the figure, EBGP peer relationships are established between neighboring routers through directly connected interfaces. The AS number is 6500X, where X is the number of the router. Both R1 and R4 have static routes to 192.168.1.0/24, which are imported to BGP through the import-route command. The maximum number of equal-cost EBGP routes for load balancing is set to 8 on R3. By default, which of the following is the number of equal-cost routes from R3 to 192.168.1.0/24?

Question # 39

Options:

A.  

3

B.  

2

C.  

1

D.  

8

Discussion 0
Question # 40

As its network scale expands, an enterprise plans to move scattered servers to the same equipment room for unified management. During hardware migration, network engineers do not need to perform device commissioning and therefore do not need to work out a migration solution.

Options:

A.  

TRUE

B.  

FALSE

Discussion 0

H12-831_V1.0 PDF

H12-831_V1.0 PDF (Printable)
$46.5
$154.99

H12-831_V1.0 Testing Engine

H12-831_V1.0 PDF (Printable)
$51
$169.99

H12-831_V1.0 PDF + Testing Engine

H12-831_V1.0 PDF (Printable)
$63.9
$212.99

Free Exams Sample Questions